Best Craftsman 113 Table Saw Fence Upgrade
Best results for craftsman 113 table saw fence upgrade
Leecraft CR-1 Zero Clearance Table Saw Insert (For Craftsman/Sears)(Colors May Vary)
$31.41
$36.75
Amazon.com
Last update was on: September 23, 2024 10:31 am
- Elimantes dangerous gap around blade where thin off-cuts can get wedged
- Fits: Sears Craftsman 10" belt-drive models 1977 to mid 2004 (check size, see DL-1U), RIDGID TS2412, TS2424, TS2400
- Measures: 14" x 3-3/4" x 3/16" (PLEASE MEASURE before ORDERING)
- Offers superior rigidity, flatness, durability, and low friction
- reduces chip-out and splintering
- PLEASE NOTE: CR-1 does not fit models TS2400LS, TS2400-1 or the new TS2410 (See RG-2)
WDEAHK 4 in 1 Earphone Cable Converter Compatible
$389.00
$431.79
Amazon.com
Last update was on: September 23, 2024 10:31 am
- Uses existing hole pattern for Delta Unisaw, Contractor, Powermatic 66, Sears 10-inch saws
- 40-inch right and 10-inch left of blade
- Fence mounting system allows full adjustment for accuracy
- Micro adjustment and aux table support. Rip Capacity Right:40,Rip Capacity Left:10,Fence Bar Length:42 inch,Front Rail Diameter:2 inch
- Guide rails supported by brackets, 2-1/2-inch fence height
Grizzly G2535 Single-Phase Motor with 3450 RPM
$250.95
$283.57
Amazon.com
Last update was on: September 23, 2024 10:31 am
- All our motors are standard NEMA 56 frames and fit over 90% of the woodworking machinery on the market.
- Size: 1-1/2 hip
- Type: Enclosed
- Made to demanding specifications these motors feature the same quality as the motors we install in our heavy-duty machines.
Delta Power Equipment Corporation 847962005250 Fence System
$211.97
$298.88
Amazon.com
Last update was on: September 23, 2024 10:31 am
- One piece square tubular rail
- Mounting design attaches to Delta table saws including Contractor Saw, Hybrid Saw, and Unisaw models
- Three-point locking system with twin hairline pointers to assure fence is parallel to blade and accurate to within 1/64 of an inch (0.4mm)
- Easy-gliding, steel tube fence body to handle quick, precision ripping, and square cuts
- Fence securely clamps to front tube and hooks over rear rail to allow for fence attachments
Craftsman 21833 Table Saw Zero-Clearance Insert CR-4
$33.95
$50.25
Amazon.com
Last update was on: September 23, 2024 10:31 am
- LEECRAFT Model Number CR-4
- Fits Craftsman 21833, Grizzly G0715P, Dayton 4KXD1, Masterforce 240-0036 table saws
- 15-1/8" x 4" x 1/8" thick with pre-milled blade, dado and riving knife slot
- Precision machined from melamine faced high density phenolic laminate
- Installation instructions included
Kreg PRS5000 Precision Router Lift
$299.00
$406.64
Amazon.com
Last update was on: September 23, 2024 10:31 am
- Allows precise above-the-table setup changes for table-mounted routers
- Above-table collet access allows fast, easy, above-table bit changes
- 3⁄8" x 9 1⁄4" x 11 3⁄4" (9.5 mm x 235mm x 298mm) Hard-anodized aluminum plate won’t Sag, resists scratches
- Fits all Kreg Router tables and many competitive brands
- Bearing-guided carriage provides smooth operation
